peugeot forums, peugeot Information,Peugeot Photos, Peugeot Reviews
Peugeot Central
Peugeot Central :: View topic - cam to crank sync ?

Peugeot Central Forum Index >> Peugeot 307 forum >> cam to crank sync ?
Post new topic Reply to topic printer-friendly view
View previous topic - View next topic
cam to crank sync ?

andi8978

On the Grid On the Grid
Joined: Jun 06, 2010 Posts: 27 Location: newbury Posts Left: 4
Status: Offline
What Peugeot do you own?: 307
How did you find Peugeot Central?: Google
Age: 31
Gender: Male
Insurance renewal month: January

PostPosted: Sun 06 Jun, 2010 10:06 am Reply with quote
hi all i am new

i have a 307 2.0 hdi 110 bhp eng rhs
having a few problems car in limp home mode and i have a few fault codes but i have forgot the p numbers (will upload soon)

cam to crank sync (cam and crank sensor been replaced) with oe parts's but when i erase fault codes this code has vever gone away even with engine not running ?

supply voltage to sensor's this also will not erase with engine off

exhaust pressure sensor detected when engine in off position this will erase but will come back when engine run even for 30 second's

air mass flow sensor signal

also driving the car last week drives fine will rev over 3000 rpm but a bit down on power but then the esp light will come on and them rev limited to 300 rpm

where i work we run autodiganos system very good but a bit limited on the particulate side off things but i can read fault code's and no code's but will let me regen i think ! when selected the screen displayed showed the it had reached limit of 60(not sure what) but when reset back to 0 esp light whent out ?

i am not sure in the exhaust pressure sensot if the pipe's are on the right way it has a new type senser fitted

i have checked a vacum pipe's all look ok but not sure if they are the right way around ?

please any help would be great  Embarassed
Back to top
View user's profile Send private message
Advertisement
PeugeotCentral.co.uk
Advertisement
Re: cam to crank sync ?

Crow

Deluxe Deluxe
Joined: Oct 28, 2007 Posts: 1738 Location: Swindon / Wiltshire Berkshire border Posts Left: 0
Status: Offline
What Peugeot do you own?: 407
How did you find Peugeot Central?: MSN
Age: 33
Gender: Male
Insurance renewal month: January

PostPosted: Tue 08 Jun, 2010 3:48 pm Reply with quote
Hi

sound like your a bit lost  , are you looking to do this work your self?? if not im quite close to you and have Peugeot / Citreon diagnostic setup which will communicate with FAP syatem and all other ECUs

otherwise for limp mode id be looking at possible wiring short , or vac system , solenoids or pipe routing , also possible particulate filter is blocked , are you sure its in limp , not just flat??

Crow
Back to top
View user's profile Send private message Send e-mail
Re: cam to crank sync ?

toddy

Moderator Moderator
Joined: May 21, 2009 Posts: 2681 Location: ilkley,west yorkshire Posts Left: 1
Status: Offline
What Peugeot do you own?: 307
How did you find Peugeot Central?: Google
Age: 36
Gender: Male
Insurance renewal month: January

PostPosted: Tue 08 Jun, 2010 7:29 pm Reply with quote
hi,,,with a cam/crank synch fault,have you scoped both sensors??4
have you checked timing belt has not jumped??

ideally post all p-codes.

toddy
------------------------------------------------------------------------------------------
so lucky to work on french!!!!!
Back to top
View user's profile Send private message MSN Messenger
Re: cam to crank sync ?

andi8978

On the Grid On the Grid
Joined: Jun 06, 2010 Posts: 27 Location: newbury Posts Left: 4
Status: Offline
What Peugeot do you own?: 307
How did you find Peugeot Central?: Google
Age: 31
Gender: Male
Insurance renewal month: January

PostPosted: Wed 09 Jun, 2010 5:57 pm Reply with quote
hi been checking a few thing's

found the ecu has lost a 5 volt feed to the cam sensor and the particulate presure sensor of which share the same live feed wire from ecu ! check all feeds and earths to the ecu all good looks like a ecu fault are these common ?

code's i have are

p1614 supply to sensors
p0340 cam/crank sync
p1429 diff exhaust pressure signal
p0100 flowmeter signal

and i have a code d208 no info on this code this is in abs/esp
Back to top
View user's profile Send private message
Re: cam to crank sync ?

toddy

Moderator Moderator
Joined: May 21, 2009 Posts: 2681 Location: ilkley,west yorkshire Posts Left: 1
Status: Offline
What Peugeot do you own?: 307
How did you find Peugeot Central?: Google
Age: 36
Gender: Male
Insurance renewal month: January

PostPosted: Wed 09 Jun, 2010 6:17 pm Reply with quote
hi,,if poss post last 8 digits of chassis number,then i can look at wiring more closely.

not a common issue that i encounter.

toddy
------------------------------------------------------------------------------------------
so lucky to work on french!!!!!
Back to top
View user's profile Send private message MSN Messenger
Re: cam to crank sync ?

andi8978

On the Grid On the Grid
Joined: Jun 06, 2010 Posts: 27 Location: newbury Posts Left: 4
Status: Offline
What Peugeot do you own?: 307
How did you find Peugeot Central?: Google
Age: 31
Gender: Male
Insurance renewal month: January

PostPosted: Wed 09 Jun, 2010 6:44 pm Reply with quote
REG    PY51 CNU    CHASSIS NO VF33CRHSB82183763

CHEERS
Back to top
View user's profile Send private message
Display posts from previous:
Peugeot Central Forum Index >> Peugeot 307 forum >> cam to crank sync ?
Post new topic Reply to topic printer-friendly view


Page 1 of 1
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum






Spambot Killer
Site Map
[backend] [backendforums] [backenddownloads] [backendlinks] [Validate robots.txt]
Car insurance from TheAA || Motorhome|| Motorhome Accessories || Motorhome Solar Panels || Labrador Forums || Caravan Forums || Motorhome Insurance
Fiamma Products